Every drawing that reaches a machining factory carries a quiet question the quote rarely answers aloud: can the factory actually hold these numbers, lot after lot? The tolerance and the surface finish are promises about a process, and the process has to deliver them across every part in the order, not once, not on a good day, but consistently.
- Production envelope: ±0.003 mm on machined and turned features, ±0.002 mm on precision-ground surfaces, with capability at Ppk ≥ 1.67 at the initial study on key characteristics and Cpk ≥ 1.33 on general characteristics. Capability is reported per characteristic: every report names the feature, its tolerance band, the sample size, the sigma method, and the study window.
- Finish by process: Ra 1.6 µm from a standard cut, Ra 0.8 µm from a controlled finish pass, Ra 0.2–0.4 µm from precision grinding.
- Where to spend precision: the features that mate, seal, slide, or establish datums, and nowhere else.
- Proof on the part: CMM measurement to the drawing datum frame with named instruments, plus capability data where the function demands it.
What is the production envelope a China machining factory holds?
A capable China machining factory works inside a production envelope it can defend with data: ±0.003 mm on machined and turned features and ±0.002 mm on precision-ground surfaces, with process capability at Ppk ≥ 1.67 initial on the characteristics the part depends on. Features inside the envelope are everyday production; features beyond it are possible but rare, because they need a different process class, tighter environmental control, or special handling, and all of that shows up in the price and the schedule.
The capability statement is the part of the envelope that matters most. A factory that occasionally lands inside the tolerance is different from one whose process is centered and stable enough to run at Ppk ≥ 1.67 initial, because the second produces lots that pass while the first produces parts that vary. The buyer who needs a production lot — not a prototype, not a sample — is buying the capability, and the capability is what the data should demonstrate.
Ask the factory to state its envelope in the quote rather than discovering it at the first article. A factory that names the standard it holds and the proof it can produce is pricing real work. A factory that promises any tolerance without a process behind it is quoting hope, and hope has a way of becoming a deviation report when the parts are measured.
How do you decide which features deserve the tight numbers?
The drawing should spend precision where the part spends its function. Features that locate the part in its assembly — the datums — must be held precisely, because every other dimension is measured from them. Features that mate with other components, such as a bearing seat or a press-fit diameter, need the tight band to work. Seal faces need flatness and finish as much as size. Those are the features where a tight callout changes whether the part works.
Features that do not function should not carry the tight numbers. Clearance holes, cosmetic pockets, and non-functional profiles do their jobs at the general tolerance. When they are specified tight, the factory has to slow down, inspect, and reject parts for features that never mattered, and the buyer pays for that in the quote and the schedule. The waste is invisible on the drawing and unmistakable on the invoice.
The pattern to avoid is one tolerance everywhere for convenience. Uniform tightness makes every feature a controlled feature, which raises the cost of the whole part for the benefit of a few. State the general tolerance on the drawing, call out the functional features individually, and let the factory machine the body of the part in a stable setup while spending its care where the design actually spends its function.
What surface finish goes with each machining process?
Surface finish is tied to process, and the drawing should name the finish the process can actually deliver. A standard milling or turning pass produces around Ra 1.6 µm — the correct specification for structural and mounting surfaces. A deliberate finishing pass reaches Ra 0.8 µm for seal seats, sliding faces, and controlled appearances. Precision grinding delivers Ra 0.2–0.4 µm for surfaces that bear or seal under load. Each of these belongs to a different process step, and specifying a ground finish on a surface that will only be machined is specifying a process the drawing does not name.
The roughness number does not travel alone; it carries a process with it. Ra 0.8 µm can be produced by a fine machining pass or by polishing, and the two behave differently in service. Where the lay direction matters — a seal or sliding surface performs differently with the tool marks in one direction than the other — the drawing should say so. The complete callout names the value, the process, and the direction, and that is the callout a factory can price without guessing.
Match the finish to the function rather than to fashion. A face that seals earns the controlled finish; a face that nothing touches earns the standard finish it gets for free. The drawing that reserves fine finishes for functional faces gets the functional result at the process-appropriate price, and the one that polishes everything pays polishing prices for surfaces that will never be touched.
How much do tighter numbers change the cost and the calendar?
Tolerance and finish alter cost through process class, and the jumps are where the money concentrates. A feature at ±0.05 mm is handled in the ordinary process. At ±0.003 mm it requires controlled conditions and careful measurement. At ±0.002 mm it becomes grinding work — a separate machine, a separate setup, and a separate inspection. The price does not scale smoothly; it steps when the part crosses a process boundary, and each step also adds days to the calendar.
Finish adds to the calendar in the same way. Ra 1.6 µm is produced in the normal cycle; Ra 0.8 µm costs a finishing pass; Ra 0.2–0.4 µm costs a grinding operation with its own queue. On a factory floor, every extra process step is another queue the part must wait in, which is why over-specified finishes and tolerances stretch delivery dates as well as prices. The two penalties travel together.
The drawing review is the tool that finds the unnecessary steps. A factory that returns the features driving cost and calendar, with the reason and the trade-off, is engineering your part. One that prices everything at the tightest number without a comment is pricing your drawing's worst interpretation. The review is where the part gets designed for its process, and a part designed for its process is the one that arrives on time at the quoted price.
Why do geometric tolerances matter more than the size bands on assembled parts?
Size tolerances control how big a feature is; geometric tolerances control where it sits and how it is oriented. On a part that assembles, position, flatness, parallelism, and perpendicularity often decide whether the assembly works — a hole that is the right size but in the wrong place, or a face that is the right height but leans, defeats the size tolerance entirely. Geometric callouts are the tolerances that connect the part to its neighbors, and they deserve their own care on the drawing.
Geometric tolerances also impose their own measurement. Position and form are verified against the drawing's datum reference frame, which requires a CMM and measurable datums. A factory that quotes geometric tolerances should be able to name the measurement method during the review, because a callout that cannot be measured is a callout that cannot be held. The measurement plan is part of the specification, not an afterthought.
Keep the datum structure as simple as the assembly allows. Datums define how the part is located in measurement and in service, and every extra datum adds fixture and measurement complexity. Define the faces the assembly locates from, dimension the rest to them, and the factory can hold the geometry and prove it. The clean datum structure is the one the inspection report can document against the same frame the designer intended.
How should the numbers on the drawing be verified on the part?
A tolerance is a claim until it is measured, and the measurement should follow the drawing's intent. Critical size and position are measured against the datum reference frame on a calibrated CMM, with the instrument and its calibration identified on the report. Surface finish is measured with a profilometer over the specified area and direction. The measurement method should be agreed at the RFQ so the report that arrives is the report the drawing needs.
Read the report the way an auditor would. Do the critical features trace to the drawing's datum structure, or are they convenient readings? Are the instruments named and calibrated? Does the report carry capability data where the contract calls for Ppk ≥ 1.67 initial? A report that answers these questions is evidence that the factory's process was in control; one that does not is a document with numbers attached.
Measurement uncertainty belongs in the same conversation. A CMM carries its own error, and on a thin tolerance band the difference between the reported value and the true value consumes the allowance. A factory that discusses this margin is measuring honestly; one that quotes numbers without it is reporting hope. The quality page on this site lists the inspection instruments behind our reports and how the data links to each lot.
What do secondary operations do to the tolerance and finish after machining?
The machine is not the last stop for most parts, and the operations that follow change the geometry and the surface. Anodizing adds a coating that grows dimensions; plating adds thickness; heat treatment can distort; blasting changes the finish that was just measured. A factory that quotes a tolerance without naming the operations after the machine is quoting a tolerance that will not survive the full process chain.
The drawing should name the sequence. A bore that must finish at ±0.003 mm after anodize has to be machined with the coating in mind, or masked, or finished after coating. A ground face that is plated afterwards is a different geometry than the ground one. When the sequence is on the drawing, the factory can quote the real process, and when the factory quotes the real process, the delivered part meets the drawing.
Measure the part in the condition it ships. The inspection that counts is the inspection of the finished part, after every coating and surface operation has run, because the part the assembly receives is not the part the machine produced. The services overview on this site describes the process chain we manage and where the inspection points sit.
What should the RFQ contain so factory quotes are comparable on tolerance and finish?
The quotes a buyer receives are shaped by the RFQ that produced them. A toleranced drawing with the datum structure, geometric callouts, and finish notes closes the largest questions. The material grade and condition, the quantity, the general tolerance standard, and the documentation requirements close the rest. Each element of the RFQ removes an assumption the factory would otherwise make, and each removed assumption makes the quotes comparable.
Ask each factory to state its process assumptions with the price: the machine class, the number of setups, the finishing operations, and the inspection scope. A quote that names the process chain is a quote that can be evaluated against the drawing. A quote that returns only a number is a quote that hides its assumptions until the first article, which is the most expensive moment to discover them.
Then compare on the whole cost, including the risk. The factory that holds the envelope, names its process, ships the documentation, and measures in the shipped state is delivering what the drawing demands. The factory that undercuts the price and discovers the requirements at the first article is delivering a discovery instead. The buyer who compares complete quotes — tolerance, finish, process, proof, and terms together — gets the part at the price it genuinely costs to make.
One habit makes the whole tolerance-and-finish conversation cheaper over time: keep the lessons of each order. When a part ships and the report comes back, note which features were hard to hold, which finishes carried the cost, and which callouts never mattered. The next drawing inherits that knowledge — tighter where the evidence supports it, looser where it does not — and every improved drawing quotes lower, machines faster, and arrives sooner. The envelope in this guide is the starting point, and the record of real parts is what refines it.
Frequently Asked Questions
What tolerance can a China machining factory realistically deliver?
Milled and turned features hold ±0.003 mm in a controlled process, and precision-ground surfaces reach ±0.002 mm, with capability at Ppk ≥ 1.67 at the initial study on key characteristics and Cpk ≥ 1.33 on general characteristics. Capability is reported per characteristic: every report names the feature, its tolerance band, the sample size, the sigma method, and the study window. Beyond that envelope the part changes process class and price.
Where should the tight tolerances go on my part?
On the features that function — datums, mating diameters, bearing seats, and seal faces. Clearance and cosmetic features run at the general tolerance, because uniform tightness raises cost and calendar without improving the part.
What surface finish should I specify for each process?
Ra 1.6 µm for a standard machining pass, Ra 0.8 µm for a controlled finish on functional faces, and Ra 0.2–0.4 µm for precision-ground surfaces. Name the value with the process and the direction, and reserve fine finishes for the faces that function.
How much do tight tolerances and fine finishes affect the price?
They affect it at the process-class boundaries. Grinding a feature or a finish adds a machine, a setup, and an inspection routine, and each also adds days to the schedule. A drawing review that names the cost-driving features is the honest way to price them.
How do I verify that the factory held my tolerances?
Measure the critical features against the drawing's datum frame on a calibrated CMM, with the instruments identified on the report, and ask for capability data at Ppk ≥ 1.67 initial where the contract requires it. Measure in the shipped state, after any coating.
Do coatings and finishing change the tolerance of my part?
Yes. Anodizing and plating add material, heat treatment can distort geometry, and blasting changes finish. The drawing should name the sequence, and the critical features should be measured in the shipped condition.
What should I send to a factory to get comparable quotes?
A toleranced drawing with datums, geometric callouts, and finish notes; the material grade and condition; the quantity; the general tolerance standard; and the documentation. Factories then quote the same scope and the differences become readable.
